Fireplace Fitter Perth Scotland (PH1): A good way to add some charm to any Perth home is by installing a brand new fireplace, or renovating an existing one. Nippy winter evenings can become enjoyable as you sit beside your fireplace listening to the crackle of firewood, and if your fire is combined with a back boiler you can also enjoy a plentiful supply of hot water too.
But before you begin smashing down the walls of a boarded over fireplace there are some vital considerations you must bear in mind to achieve a safe and efficient fireplace. Any work that is carried out on your hearth, fireplace, flue lining and chimney breast must comply with the building regulations, Part J for combustible appliances. If you own a listed building you'll also need to find out if planning permission is required from the local council before any work commences.
DIY OR PROFESSIONAL FIREPLACE INSTALLATION?
You may be able to do some of the work in remodeling an existing fireplace if you have the ability needed, but there is always a problem in finding structural and safety issues that need to be resolved by a professional tradesman. It could be that so as to get a fire roaring once more you will need nothing more than a good clean of the hearth and a sweeping of the chimney. What's more typical however is an area of old, crumbling brickwork that hides a stopped up flue, and also requires some form of structural reinforcement before it can be used safely.
Owing to the acute health and fire risk problems that can result from an improperly fitted or renovated fireplace, it is better to avail yourself of the knowledge and experience of a specialist fireplace fitter and builder in Perth. There always has to be enough airflow into a room where there is a fireplace to guarantee sufficient levels of oxygen allow the fire to burn properly. If there is not enough airflow then it's possible that a fire will burn inefficiently and cause a build-up of carbon monoxide, which can be lethal.
To effectively get over any airflow issues, vents may be installed around the room during a fireplace installation, to guarantee suitable oxygen levels reach the fire. They may have to install vents into unused chimney flues which can trap moist air and cause staining and damp spots on your chimney breast.
BEFORE WORK COMMENCES
It is astonishing how much soot and dust can build up inside an old fireplace and chimney and you will not know what's there until you open it up. A thoughtful Perth fireplace installer will bring dust sheets to cover up your home furnishings and supply some form of protection, however it's sensible when possible to remove furniture and woven floor coverings from the room before work starts. If you are carrying out a complete restoration of a room or property, the fireplace ought to be opened up before any plastering or decorating is undertaken. This should help to avoid any impairment by soot and dirt to any previously completed work.
STRUCTURAL AND CONSTRUCTION WORK
Once you've opened up your old fireplace you'll have a better idea of what work needs to be done, and also be able to thoroughly sweep the chimney and clear out any hearth that is still in position. You should now contact your chimney sweep, if you haven't already done so, to come and look at the old fireplace and chimney. A chimney sweep will first clean the flue and while doing this will inspect the condition of the chimney and provide you with advice on whether a new flue liner is needed.
If it is necessary to strengthen the chimney or install a flue lining all relevant Building Regulations must be followed to the letter. A competent fireplace installer in Perth will be needed to accomplish this task, and will need the knowledge and skills in construction to closely follow all regulations.
If the dimensions of the existing fireplace are bigger than your requirements, a concrete supporting lintel must be put in. When your new concrete lintel is safely in position you may now get on with the updating, installation and repair of the fireplace hearth. If the current hearth is set into the floor you'll need to raise it above floor level to observe the latest regulations. Pre-made options from concrete, marble or slate are available on the market to achieve this, or your fireplace builder in Perth may be able to offer you a bespoke, tailor-made hearth to complement the style of your room.
STYLES OF FIREPLACE
Choosing your perfect fireplace can be difficult when faced with the various shapes, sizes and designs available from an online shop or fireplace showroom. The advice and suggestions from your sales and installation team, which will be specific to your requirements, will enable you to pick a fireplace that's both perfect for your chimney and flue, and suited to your decor.
You property's age, and the theme that you're trying to create for your room, should all help you to decide on the type and design of fireplace which is most suitable. For example, an inglenook fireplace can be a wonderful backdrop to a traditional cast iron wood burning stove, which highlights its charm and deflects the heat into the room.
A wood burner is also a good option if your Perth home does not have a chimney breast. This style of fireplace can be fitted with a stainless steel flue which is channeled through an external wall and doesn't need a chimney, to be installed safely.
ELECTRIC, MULTI-FUEL, GAS, OPEN OR WOOD FIREPLACE?
A crackling fire on a cold, dark evening creates an ambience and charm that cannot be matched, however what are the other options available to put into in your new fireplace in Perth?
Open Fireplaces - The traditional fireplace that can make use of various fuels such as briquettes, wood, coal and other combustive materials. In earlier times an open fire might have had the associations with being smoky, draughty and inefficient, however a well installed contemporary fireplace is a joy to sit in front of and laze in the warmth it provides.
Wood Burning Stoves - Wood burning stoves have become "the in thing" in a lot of properties in Perth, and can have modern or classic design to match your furnishings. A back boiler is an added benefit and could provide steaming hot water for personal use, or for heating in another area via a radiator.
Multi-Fuel Stoves - As the name suggests multi-fuel stoves can be fired up with with a range of fuels, such as oil, gas, smokeless coal or wood, and become a unique focal point in any kitchen or living room in Perth. Some types, like the AGA range of multi-fuel stoves, are also suitable for cooking, providing hot water and heating your entire house.
Gas Fireplaces - There are a range of styles to suit all home types and their effectiveness in warming a room is superior to open fireplaces or wood burning stoves. Have to be professionally installed and maintained by Gas Safe registered (previously CORGI registered) technician.
Electric Fireplaces - Simple installation and a varied choice of designs make electric fires the obvious choice for Perth properties that don't have a chimney. Even if your property has a conventional fireplace, an electric fire that looks almost like a "real" fire can be installed.
Fireplace installation is available in Perth and also in: Ruthvenfield, Rhynd, Letham, Luncarty, Inveralmond, Almondbank, Forgandenny, Muirton, Craigie, Tibbermore, Kintillo, Craigend, Bridgend, Lethendy, Scone, Elcho, Old Scone, Gannochy, and in these postcodes PH1 1EQ, PH1 1NQ, PH1 1DS, PH1 1RL, PH1 1DR, PH1 1LR, PH1 1PR, PH1 1QD, PH1 1BB, PH1 1EY. Locally based Perth fireplace specialists will probably have the postcode PH1 and the telephone dialling code 01738. Checking this should confirm you access locally based tradesmen installing fireplaces. Perth householders will be able to benefit from these and countless other comparable services.
A crucial addition to the chimney system on your house, a flue liner improves the safety of your chimney while enabling it to perform more effectively than it otherwise would. With the purpose of transporting fumes to the outside of a building, flue liners are conduits made of metal, ceramic material or clay which are fitted to the inside of chimneys. Depending on their age and condition, older chimneys in Perth may have to be re-lined, or might not be fitted with a flue liner at all.
Your fireplace flue lining can, over time, be compromised by the hazardous gases which are formed by burning a fire. While it's being cleaned, get the sweep or fireplace specialist to inspect your flue for any impairment or prospects of it malfunctioning in the foreseeable future. You have to stop those harmful gases from leaking into your home, which is what can transpire when a flue is impaired. There is an added risk with busted flue linings, in that they can allow extreme heat to pass into the chimney's structure, which could contribute to fires.
Chimney Sweep Perth
The regular sweeping of your chimney is imperative if you've got an open fire or a stove in your house in Perth. To be completely safe, it is best to clean and sweep your chimney once or twice a year, particularly if you're burning wood or bituminous coal.
It is invariably best to call in a professional Perth chimney sweep if you want to get this done correctly. This not only means that you chimney is kept nice and clean, the chimney sweep will also be on hand to spot any problems with you chimney.
A build-up of ash, soot and wood tar can cause chimney fires if you neglect to sweep your chimney. Harmful carbon monoxide gas can also flow back into your home if you allow your chimney to become blocked.
In the unlikely event that any damages or accidents occur while you are having your chimney swept, make certain your chosen Perth chimney sweep has public liability cover. For Perth chimney sweep quotes CLICK HERE. You should also be able to access chimney sweeping services in Ruthvenfield, Rhynd, Letham, Luncarty, Inveralmond, Almondbank, Forgandenny, Muirton, Craigie, Tibbermore, Kintillo, Craigend, Bridgend, Lethendy, Scone, Elcho, Old Scone, Gannochy, and and of course in Perth.
Improve the Cost-Efficiency of Your Open Fireplace
The classic fireplace may have lost some of its glamour due to worries about the environment but it is still loved by many in Perth. Sitting in front of the comfort of a fireplace, brings back many treasured memories for lots of folks. There are many benefits to having a fireplace although there are a few negative aspects that might need to be taken care of. As power costs climb, you should make sure that your fireplace is producing heat in an efficient way. While having a fire alight in a fireplace keeps those close to it warm, it can actually suck warm air from the rest of the area, causing your heater to work harder. If you do not have a fire lit, the damper is intended to keep heat in. Regrettably, dampers have a very inadequate seal, so chilly air gets in, and warm air can get out.
What many folks in Perth don't understand about their fireplace is that it doesn't always do what they believe it is doing. Instead of managing the heating of a residence naturally, a fireplace can in fact add hundreds of pounds to the cost of your heating. Nevertheless, there are some techniques that can be done that will be able to turn your budget busting fireplace into something much more efficient. There tend to be four simple steps that you can take to change your fireplace into the cost-effective heat sourse you're looking for. These definitely will make your fireplace far more effective, and lower your energy bills.
Step one is to take out your current damper and change it for a top sealing damper. This style of damper is installed at the top of the chimney, and works like a storm door. The top sealing damper will keep the air in the house from getting away and works effectively in both cold and hot weather conditions. It's not that tricky to fit and may be easily bought on the web. A second thing that can be done should be to position a fire-back at the back of your fireplace. It's produced from cast iron and is used to improve the appearance of your fireplace while at the same time shielding the back wall from fire damage. The fire-back also takes up heat coming from the fire and returns it back inside, making the fireplace more efficient.
Another cost saver is a fireplace heater, which heats the area by drawing the air into a chamber and blowing the air back into the room. These heating units are closed systems, hence no smoke is released, and they really can make a huge difference to the temperature of your property. Finally, you may install glass doors which could be the costliest. If you do your groundwork, you can find a good price on glass doors and fit them on your own. Glass fireplace doors will keep the air in your house from escaping and also help to protect your pets and children from fires.
All these suggestions are simple to implement, and the required products can be found online. Just do your best to keep your fireplace efficient and see your heating bill go down.
Fireplace Installation Scotland
In Scotland you will additionally find: Kemnay fireplace installers, Freuchie fireplace fitters, North Queensferry fireplace installers, Golspie fireplace fitters, Macduff fireplaces, Larkhall fireplaces, Cullen fireplace installations, Longforgan fireplace fitters, Fairlie fireplace installation, Brightons fireplace installations, Portree fireplace installations, North Kessock fireplace fitters, Edzell fireplace fitters, Cleland fireplace installation, Carstairs fireplace installers, Leven fireplace installers, Duns fireplaces, West Kilbride fireplace fitters, Clackmannan fireplace installers, Kilmaurs fireplaces, Auchterarder fireplace fitters, Renton fireplace fitters, Westquarter fireplace installation, Kelty fireplace installations, Armadale fireplace installations, New Cumnock fireplace installation, Peterculter fireplace fitters, Crieff fireplace installations, Danderhall fireplace installation, Blairgowrie fireplace fitters. In every area of the Scotland region it should be possible to locate fireplace specialists who'll offer you high quality services for your fireplace needs. If you cannot find the rightin Perth itself you shouldn't have any difficulty locating one someplace nearby.
Help, Information and Social Media
To find out about fireplaces on social media, check this out. To find out what is happening in the field of fireplace installation pay a visit to the Buildhub Forum, threads comprise pellet boilers and stoves, wood burners, building regulations, trims for stoves, widening a fireplace and chimney flues. If you're curious to read up on ideas for fireplaces click here. To learn the best way to install a wood burning stove you could have a look at YouTube videos like this. To learn more about the history of the fireplace, coal burning fireplaces, fireplace heating efficiency, the environmental effects of fireplaces, the health effects of fireplaces and the different types of fireplaces, you could visit the Wikipedia "Fireplace" page.
Skip Hire Perth
When you're doing any sort of home refurbishments or improvements in Perth, you are likely to generate quite a lot of waste. Even though fireplace installations isn't one of those jobs that normally generates lots of waste, that's not always the case, and the amount will depend on the scale of your particular installation. In many cases the tradesman you are employing will happily remove the waste that is created during the course of the work, but be warned - quite a few of them certainly don't!
Hiring a skip is one of the simplest and most hassle-free ways to get rid of this waste. Skips come in various different depending on your needs, and deciding which skip to order is essential. Most skip hire companies in Perth provide mini-skips, midi-skips, builders skips and roll-on-roll-off skips, and for different projects skip bags are also available.
To check on the current skip hire prices in Perth GO HERE.
Perth Fireplace Related Tasks
There is a wide range of work that can be carried out by your local Perth fireplace company including inset stove installation in Perth, cast iron fireplaces, the installation of chimney cowls, fire grate conversions, fireplace replacement, electric fire baskets, fireplace restoration, fireplace services, fireplaceprice quotes, modern fireplaces, fireplace surrounds, made-to-measure fireplaces, fireplace removal, freestanding stoves in Perth, chimney repairs, cast iron fireplace installations Perth, multifuel stoves, fireplace inserts in Perth, stone fireplace installations Perth, fireplaces in Perth, marble fireplace installations, fireplace installation, limestone fireplace installations in Perth, double-sided stove installations, fireplace fitting in Perth, fireplace suites, chimney modifications, fake fireplace installation, and lots more. Listed are just a handful of the duties that are undertaken by those installing fireplaces. Perth companies will let you know their full range of services.
Fireplace Installers Near Perth
Also here.: Almondbank fireplaces, Craigend fireplaces, Bridgend fireplaces, Old Scone fireplaces, Lethendy fireplaces, Forgandenny fireplaces, Tibbermore fireplaces, Letham fireplaces, Ruthvenfield fireplaces, Luncarty fireplaces, Scone fireplaces, Kintillo fireplaces, Gannochy fireplaces, Craigie fireplaces, Inveralmond fireplaces, Rhynd fireplaces, Muirton fireplaces, Elcho and more. The majority of these areas are covered by tradesmen fitting fireplaces. Perth home and business owners can get quotes by clicking
- Perth Brick Fireplaces
- Perth Wood Burning Fireplaces
- Perth Cast Iron Fireplaces
- Perth Fireplace Mantels
- Perth Fireplace Installation
- Perth Fireplace Repair
- Perth Marble Fireplaces
- Perth Fireplace Installers
- Perth Victorian Fireplaces
- Perth Stone Fireplaces
- Perth Fireplace Surrounds
- Perth Gas Fireplaces
- Perth Fireplaces
- Perth Fireplace Fitters
Fireplaces Around Perth: In Rowan Terrace, Milne Court, Jura Street, Fraser Terrace, Mavisbank Gardens, Christie Place, Lagavulin Place, Pickembere, Brahan Terrace, Linnet Drive, Tulloch Square, Dower Place, Moredun Terrace, Cleeve Drive, Craigie Knowes Road, Malloch Avenue, Buchan Road, Monument View, Crammond Place, Pickletullum Gardens, Broom Side, Princes Street Mews, Highpoint, Clyde Place, Rosebank, Allan Terrace, Glenfarg Terrace, Cavendish Avenue, as well as the following local Perth postcodes: PH1 1EQ, PH1 1NQ, PH1 1DS, PH1 1RL, PH1 1DR, PH1 1LR, PH1 1PR, PH1 1QD, PH1 1BB, PH1 1EY. householders have just recently needed fireplace installation. Work was carried out in these places by local installers of fireplaces. Perth business and home owners benefited from professional and dependable fireplace services.
More Perth Tradespeople: Home improvement projects in Perth will often require the expertise of several different craftsmen, and a tiler in Perth, a bricklayer in Perth, an odd job man in Perth, a floor fitter in Perth, a roofer in Perth, a painter and decorator in Perth, a carpenter in Perth, a builder in Perth, a plumber in Perth, a chimney sweep in Perth, an electrician in Perth, waste removal in Perth, a plasterer in Perth, a cleaner in Perth, SKIP HIRE in Perth, a stonemason in Perth may be needed despite the fact that you are currently attempting to find in Perth, Scotland. Click on the links to get quotations for all kinds of home improvement project.
If you need local Perth info take a look here
More Scotland Fireplace Fitters: More Greenock, Dunfermline, Paisley, Kilmarnock, Falkirk, Airdrie, Cumbernauld, Hamilton, Perth, Motherwell, Livingston, Ayr, Aberdeen, Glasgow, Stirling, Irvine, Coatbridge, Glenrothes, Kirkcaldy, East Kilbride, Inverness, Dumfries, Dundee and Edinburgh.:
Fireplace installation in PH1 area, phone code 01738.